#MILLUMIN FORUM SOFTWARE#
#MILLUMIN FORUM CODE#
#MILLUMIN FORUM LICENSE#

check to see if you just pressed the button read the state of the switch into a local variable: Unsigned long lastDebounceTime ДЇor (int thisPin = 0 thisPin = 0 thisPin-) Hi everyone, IвЂ™m trying to wrap my head around the coding but, even with your suggestions, IвЂ™m not able to set a debounce time for the buttons connected to my arduino. I'll try all the coding and get back to you all. Have you looked into dance game mats? Here. My thought about FSR is that maybe the carpet will be quite heavy and there could be no room for a possible threshold and the maximum pressure readable by the FSR? I have not much experience with those.

I have two FSR, but what I've found are quite small and I could need to make an array of those to make them work. You could probably even find a few DIY guides to build your own. The old-style pressure mats used in ancient burglar alarms are still available.

#MILLUMIN FORUM SOFTWARE#

It will be a continuous cycle of videos and sounds played by the Millumin software with Arduino taking care of the buttons and interaction.ДЇor buttons under the carpet, you're looking for Force Sensitive Resistors or FSR. Attendants will have only to turn it on and off and I can make all the start up automatic. The installation will be fixed in one space for a week, non need to pull it off. The cost of having staff pull up the carpet each night to re-solder wires that broke will exceed the purchase cost very quickly. How long is this installation expected to last? If it's going to be more than a week then reliability is going to be the biggest problem.

#MILLUMIN FORUM CODE#

I'll try the code hints in the next days and give you an update. Hi everyone! Many thanks for all the replies. Maybe you could use FSRs for the buttons? Might not work the thick map and lack of weight. remove from original uint8_t byte = digitalRead(id) Proposed addition to the library: void sendDigitalForID(char id, uint8_t byte) Finally we send just one frame with all our values MilluminStream::sendVariableForID(0, variable) // Add a custom value to the frame MilluminStream::sendDigitalForID(pushButton) // Add the value of D3 pin to the frame MilluminStream::sendDigitalForID(pushButton, buttonVal) Unsigned long debounceDelay = 50 // the debounce time increase if the output flickersДЇor (int thisPin = 0 thisPin debounceDelay) // last time button was pushedДЇor (int thisPin = 0 thisPin = buttonInactiveTime ) Unsigned long lastDebounceTime = 0 // the last time the output pin was toggled milliseconds, will quickly become a bigger number than can be stored in an int. the following variables are unsigned longs because the time, measured in Int lastButtonState = LOW // the previous reading from the input pin Int buttonState // the current reading from the input pin pin Digital array as input to stream its sensor value

#MILLUMIN FORUM LICENSE#

IвЂ™d like that every button beheaves this way.Д¬reative Commons Attribution-NonCommercial 4.0 International Public License I mean that if button nВ° 1 is pressed, it can be triggered again after eg.10 sec, but in the mean while the others could be triggered. IвЂ™d like to add to the code some kind of debounce, so the buttons can be triggered only after a specific time if they were triggered before.

I succeded on making the buttons work with the arduino and interface the arduino with the software Millumin that uses itвЂ™s libraries to talk with the board. The buttons are simple buttons connected with a resistor and each button is connected to a digital pin of the board. I was thinking to membrane buttons but maybe somebody knows a better solution. The kids will trigger the buttons and make specific events start.Д¬an some body point me on the direction of the type of buttons to use? Those should stay under the carpet (which is a dance carpet, so a quite heavy PVC carpet) and be triggered by the pressure applied by the audience (mostly very small kids) but have a very low profile. IвЂ™d like to use some buttons in specific places to trigger different medias and make the installation variable.

It is supposed to be an interactive carpet interfaced with Millumin software that will run several videos projected on this carpet. IвЂ™m developing an Arduino project for an installation for a kids audience and need some coding help. The previous post had some views and no reply and IвЂ™m really in need of some guidance. Hi everyone, IвЂ™m reposting this here hoping to get some reply.

Millumin forum